DN100 flange cast steel floating ball valve electric actuator

NegotiableUpdate on 05/20

Model

Nature of the Manufacturer: Producers

Product Category

Place of Origin

Online Consult

Overview

Product Display 1. Introduction to DN100 Flange Cast Steel Floating Ball Valve Electric actuator: The DN100 flange cast steel floating ball valve electric actuator is the driving device of the electric valve, which is easily matched with the valve and suitable for controlling the opening and closing of the valve, on-site control and remote control operation adjustment, bus control, etc. It is a motion device for valve and air door centralized control and automatic control

Product Details

Product Display

1DN100 flange cast steel floatingElectric actuator for ball valveIntroduction:

DN100 flange cast steel floating ball valve electric actuatorIt is a driving device for electric valves, which is easy to use in conjunction with valves. It is suitable for controlling the opening and closing of valves, on-site and remote operation adjustment, bus control, etc. It is a motion device for centralized and automatic control of valves and dampers. Suitable for ball valves, butterfly valves, dampers, etcA 90 degree rotary valve. This product has the characteristics of comprehensive functionality, control system, reliable performance, easy use and maintenance, and small size. It has been widely praised and applied in industries such as power, steel, petrochemicals, metallurgy, water treatment, and papermaking.

IIDN100 flange cast steel floating ball valve electric actuatorfeatureAnd parameters：
1. The device is dustproof, rainproof, and corrosion-resistant, with a protection level of IP55 (special orders IP65, IP67).
2. The torque control mechanism is reliable in action, easy to adjust, and has high torque repeatability accuracy.
3. Adopting a valve electric device three-phase asynchronous motor, it has the characteristics of high starting torque, low rotational inertia, long service life, and F-class insulation.
4. The work schedule is short 10 minutes (30 minutes for special orders).
5. Equipped with mechanical (conventional type) or LCD (conventional type without) valve position indicator, which can intuitively know the opening size of the valve.
6. Hand electric switching: Fully automatic switching, when manual operation is required, simply transfer the handwheel to operate the electric device; When electric operation is required, there is no need to switch the handle. (Attention: Do not transfer the handwheel while operating electrically!)
7. There are triple protections such as travel limit, over torque limit, and mechanical limit switch, ensuring the safe use of the driving device and valve.
8. Power supply: Typically 380V (± 10%), 50Hz (special orders for three-phase 660V, 415V, single-phase 220V, 60Hz)
9. Explosion proof mark: ExdIIBT4 (conventional type not explosion-proof).
10. Relative humidity of the environment: ≤ 95% (at 25 ℃).
11. Environmental temperature: -20~+60 ℃ (special orders -40~+100 ℃).

IIIDN100 flange cast steel floating ball valve electric actuatorinstall
1. During installation, avoid environments with flammable and explosive gases.
2. It can also be installed outdoors, but be careful to avoid direct sunlight and direct rain spraying.
3. Before installing the electric actuator, the pipeline should be cleaned, and a filter can be installed at the valve inlet to facilitate the removal of impurities.
4. Vertical installation has a better effect. If installed from other angles, it is necessary to ensure that the cable interface position is higher than the direction position to prevent water from flowing into the actuator along the low potential.
5. The connection between the valve body flange and the pipeline should be kept naturally coaxial to avoid shear stress, and the connecting bolts should be evenly locked.
6. During installation, a certain amount of space should be reserved to facilitate other maintenance operations in the later stage.
7. Add bypass appropriately during installation in important areas for emergency use.
8. The valve body part needs to be insulated like the pipeline, especially when used for high-temperature media, it should be insulated. Otherwise, the high ambient temperature will affect the normal operation of the electric actuator.
9. Electric actuators must not be immersed in water, and wiring must comply with regulations.
10. Before powering on, ensure that the voltage meets the standard to avoid damaging the motor.
11. During maintenance, the power must be turned off.