Manufacturer of high-efficiency filter air outlet

Manufacturer of high-efficiency filter air outletIt is the terminal equipment in air purification systems, which broadly includes laminar flow hoods, fan filter units (FFUs), self-cleaning devices, and other air supply equipment.

Structural characteristics of high-efficiency filter air outlet:

The air supply outlet is composed of a high-efficiency filter and an air supply outlet, which also includes components such as a diffuser plate and a pressure frame. The air supply outlet referred to here is not a louver air supply outlet, but is made of cold-rolled steel plate, surface treated with spray or paint, welded with lifting rings, screws and nuts (for clamping the high-efficiency filter), air inlet flange, and insulation material in the static pressure box. The conventional size and air volume of the high-efficiency filter are determined by the specifications of the high-efficiency filter installed inside. There are usually three specifications of air supply: 500M3/H, 1000M3/H, and 1500M3/H. The internal high-efficiency filters are 320 * 320 * 220.484 * 484 * 220.610 * 610 * 150.630 * 630 * 220, etc. Efficient filter. Filter frame, aluminum alloy, wooden frame, galvanized sheet folding frame, aluminum sheet folding frame.

Classification of high-efficiency filter air supply outlet:

1. The opening of the diffuser plate in the air supply outlet with a diffuser plate is generally 8MM, and the diffuser plate has a convex structure, which has a good diffusion effect on clean airflow.

2. The air supply outlet with a flat diffuser plate is located on a flat surface, with diagonal slit air outlets around the periphery and a circular hole group with a diameter of about 3MM in the middle.

3. The insulation air supply outlet is located in a clean room. In summer, the air supply temperature is lower than the indoor temperature, while in winter, it is generally more efficient than the indoor temperature. Therefore, it is necessary to perform insulation treatment on the wall of the air supply outlet to ensure that the air supply parameters meet the design requirements. The insulation air supply outlet is a type of insulation material pasted on the inner wall of the static pressure box inside the high-efficiency filter air supply outlet, and covered with a thin galvanized steel plate on the outside of the insulation material to prevent dust from falling off.

4. Top inlet air supply outlet and side inlet air supply outlet are commonly used in engineering. The requirement for top inlet air supply outlet is to have a large installation space, that is, a large space should be left above the ceiling. The inlet air flow is well diffused in the static pressure box. This type of air supply outlet is suitable for new buildings or high-rise buildings.

5. Side inlet air supply port, the air flow inside the static pressure box needs to turn, and its diffusion performance is not as good as that of the top inlet air supply port. However, it requires less installation space, and the height of the ceiling interlayer can be as small as 800mm, so it is suitable for low rise buildings, especially when existing buildings are transformed into clean rooms. However, the inlet flange should be made detachable, otherwise it cannot be installed into the installation hole of the ceiling.

Specification, size and parameters of high-efficiency filter air outlet:

External dimensions of static pressure box (MM) (width * height * depth) 370 * 370 * 530; Filter size (MM) (width * height * depth) 320 * 320 * 320 rated air volume m3/h (500) inlet duct size D * C (MM) 200 * 200;

External dimensions of static pressure box (MM) (width * height * depth) 534 * 534 * 530; Filter size (MM) (width * height * depth) 484 * 484 * 220 Rated air volume m3/h (1000) Inlet duct size D * C (MM) 320 * 200;

External dimensions of static pressure box (MM) (width * height * depth) 660 * 660 * 460; Filter size (MM) (width * height * depth) 610 * 610 * 150 Rated air volume m3/h (1000) Inlet duct size D * C (MM) 320 * 250;

External dimensions of static pressure box (MM) (width * height * depth) 1270 * 660 * 460; Filter size (MM) (width * height * depth) 1220 * 610 * 150 Rated air volume m3/h (2000) Inlet duct size D * C (MM) 500 * 200;

External dimensions of static pressure box (MM) (width * height * depth) 680 * 680 * 530; Filter size (MM) (width * height * depth) 630 * 630 * 220 Rated air volume m3/h (1500) Inlet duct size D * C (MM) 320 * 250;

External dimensions of static pressure box (MM) (width * height * depth) 965 * 660 * 460; Filter size (MM) (width * height * depth) 915 * 610 * 150 Rated air volume m3/h (1500) Inlet duct size D * C (MM) 500 * 250;

Attention to accidents during installation of high-efficiency filter air outlet:

The size of the high-efficiency filter air outlet must meet the design requirements. Clean thoroughly before installation. Efficient filters need to be installed and replaced in the clean room for the air supply outlet. The joint between the outlet flange and the ceiling panel should be sealed with a dense gasket. Install and replace high-efficiency filter vents in the technical interlayer, and pre embed short pipes in coordination with civil construction before installation.

Installation specifications for high-efficiency filter air supply outlet:

1、 The size of the high-efficiency filter air outlet must meet the design requirements. Clean thoroughly before installation. Efficient filters need to be installed and replaced in the clean room for the air supply outlet. The joint between the outlet flange and the ceiling panel should be sealed with a dense gasket. Install and replace high-efficiency filter vents in the technical interlayer. Before installation, cooperate with civil construction to embed short pipes. If there are cracks between the short pipes and the ceiling panel, they must be sealed. Damaged coating on the surface of the air vent shall not be installed. After the installation of the air outlet, it should be immediately connected to the air duct, and the open end should be sealed with plastic film and tape

2、 Before installing the high-efficiency filter air outlet, the clean room must be thoroughly cleaned and wiped clean. If there is dust accumulation inside the purification air conditioning system, it should be cleaned and wiped clean again to meet the cleaning requirements. If high-efficiency filters are installed in the technical mezzanine or ceiling, the technical mezzanine or ceiling should also be thoroughly cleaned and wiped clean.

3、 After the cleanroom and purification air conditioning system meet the cleanliness requirements, the purification air conditioning system must be put into trial operation. After continuous operation for more than 12 hours, immediately install a high-efficiency filter after cleaning and wiping the clean room again.

4、 The transportation and storage of high-efficiency filters should be placed in the direction indicated by the manufacturer's logo. During transportation, handle with care to prevent severe vibrations and collisions.

5、 Before installing the high-efficiency air supply outlet, the filter must be unpacked and visually inspected at the installation site, including whether the filter paper, sealant, and frame are damaged; Whether the side length, diagonal, and thickness dimensions meet the requirements; Whether the frame has burrs and rust spots (metal frame); Whether there is a product qualification certificate and whether the technical performance meets the design requirements. Then perform leak detection. Those that pass the inspection and leak detection should be installed immediately. During installation, reasonable adjustments should be made based on the resistance of each filter. For one-way flow, the difference between the rated resistance and average resistance of each filter on the same air outlet or supply surface should be less than 5%. High efficiency filters with cleanliness levels equal to or higher than Class 100 cleanrooms.

6、 The frame for installing high-efficiency filters should be flat. The allowable deviation for the flatness of the installation frame of each high-efficiency filter is not more than 1mm.

7、 When sealing between the high-efficiency filter and the frame using sealing gaskets, stickers, negative pressure seals, liquid tank seals, and double ring seals, the surface of the packing, filter frame surface, frame surface, and liquid tank must be wiped clean.

8、 When using a sealing gasket, the thickness of the gasket should not exceed 8mm, and the compression rate should be 25% to 30%. When using liquid tank sealing, the liquid level in the tank should meet the design requirements, and there should be no leakage at the joints of the frame. When using a double ring sealing strip, do not block the holes on the ring cavity when pasting the sealing strip; Both double ring sealing and negative pressure sealing must keep the negative pressure pipeline unobstructed.

9、 When installing a high-efficiency filter, the arrow on the outer frame should be aligned with the airflow direction *. When installed vertically, the crease seam of the filter paper should be perpendicular to the ground.

The air purification products and equipment provided by Guangzhou Zijing include air shower roomsCargo shower room, primary filter, medium efficiency filter, high-efficiency filter, ultra clean workbench, clean workbench, transfer window, air shower room accessories, air shower room controller, chemical filter, FFU fan filtration unit, air purifier, clean shed, laminar flow hood, fresh air cabinet, filter cabinet, fume hood, washbasin, dust-free shoe cabinet/dust-free wardrobe, clean sampling vehicle, air supply ceiling, high-efficiency air supply outlet, and other cleanroom and supporting purification products. Cleanroom purification equipment is widely used in electronics, semiconductors, biopharmaceuticals, food processing, nuclear industry, automotive manufacturing, air conditioning and heating industries and fields.

Zijing specializes in purification equipment and engineering, cleanroom contractors, cleanroom engineering, cleanroom construction, cleanroom cleanliness testing, cleanroom solutions, cleanroom standards, cleanroom construction, cleanroom equipment, cleanroom design, cleanroom construction, and cleanroom maintenance. Cleanrooms are also known as cleanrooms or cleanrooms.

Quality assurance of "Zijing" brand air purification equipment products:

1. Our company's "Zijing" brand air purification equipment and air filter products have been approved domestically;

2. To meet the high quality requirements of our customers for clean rooms, every air purification equipment produced by our company undergoes strict inspection by our quality inspectors and can only be shipped if it meets the product quality standards; Air filters are produced and tested in standard Class 10000 cleanrooms.

3. After the completion of product delivery and acceptance, our company will establish independent files for your company and the ordered products, in order to provide high-quality and timely services to your company in collaboration with our company.

4. Product packaging: wooden crate or cardboard box packaging;

5. Shipping method: freight;

6. Delivery time: Our company will complete production within 5 working days from the date of receipt of payment after the contract is signed, and the goods will arrive within 3 working days;

Service Objective:

7. The "Zijing" brand air purification equipment and air filters produced by the company can provide * support;

8. Fault acceptance: 48 hours outside the province, 24 hours within the province;