BURKERT flowmeter original sales

Baode BURKERT flowmeterWhen steam enters the body, a part of the steam indirectly enters the throttling element (nozzle or orifice plate) and undergoes throttling action, forming a differential pressure. Another part of the steam indirectly enters the diversion pipe through the nozzle and radiates to the impeller, which rotates to form torque. The lower part of the impeller shaft is equipped with damping blades, which rotate in a radiator filled with water, and the water acts as a damping force on the rotation of the impeller. That is, the impeller is effectively absorbing the kinetic energy of the jet, and the Baode BURKERT flowmeter rotates the impeller shaft at a speed that balances the torque of the impeller and the braking torque of the damping plate. The steam entering the body is divided into the diversion pipeline in a certain proportion, and the speed of the impeller is inversely proportional to the flow rate, so the speed of the impeller is also inversely proportional to the total steam flow passing through. The rotation of the impeller shaft is adjusted to the appropriate speed through the acceleration gear, and the Baode BURKERT flowmeter is then transmitted to the pointer of the counter through a magnetic coupling. The pointer rotates once, and the accumulated character wheel enters one character. The steam flow rate can be indirectly read on the meter head.

Baode BURKERT flowmeterInstallation has certain requirements for pipelines, with high demands for straight pipe sections. When designing a new water plant, efforts can be made to meet these requirements. However, for the renovation and installation of an old water plant, it becomes difficult to meet these conditions, which can affect the stability of the equipment The solution to this is to install rectifier tubes to improve the flow characteristics The low flow rate of the water being measured can also affect the accuracy of the measurement, especially for flow meters installed at the boundaries of some districts. Due to their location at the end of the regional company's pipeline network and small pressure difference, the flow rate is too low The solution can be to open the valves on both sides of the boundary as much as possible to improve When there is gas in the pipeline, the Baode BURKERT flowmeter will cause measurement fluctuations and instability. To solve the problem, we must find the source of the gas and solve it. If necessary, an exhaust valve can be installed in the pipeline The sensor electrode surface of the flowmeter installed in the raw water pipeline is contaminated by sediment deposition, which affects the measurement. The solution is to use scraper type electrodes and regularly maintain and clean the well. Foreign objects accumulate in the inlet pipeline of the electromagnetic flowmeter. The sudden change in the flow characteristics of the water body on the affected side affects the measurement accuracy and causes significant errors. The solution is to promptly remove foreign objects accumulated in the pipeline. The lightning strike caused damage to the converter of the electromagnetic flowmeter, making it impossible for the Baode BURKERT flowmeter to measure. The solution is to install corresponding lightning arresters at the signal input terminal, excitation current input terminal, and working power supply terminal of the converter.

Baode BURKERT flowmeterSelect the corresponding water pump based on the diameter and flow rate of the pipeline for verification testing; After the flowmeter is correctly installed and connected, it should be preheated for about 30 minutes by powering on according to the requirements of the calibration regulations; If using a high-level tank water source, check whether the overflow signal of the stabilizing water tower appears. Before the formal test, according to the requirements of the calibration regulations, the calibration medium should be circulated in the pipeline system for a certain period of time, and at the same time, the sealing parts in the pipeline should be checked for any leakage; Before starting the formal calibration, the calibration medium should be filled with the tested flowmeter sensor, and then the downstream valve should be closed for zero position adjustment; When starting the calibration, the valve at the front end of the pipeline should be opened first, and the Baode BURKERT flowmeter should slowly open the valve behind the verified flowmeter to adjust the flow rate at the calibration point; During the calibration process, the flow stability of each flow point should be within 1% to 2% - using the flow method, while the total amount method can be within 5%. When completing the calibration process of a flow point, the temperature change of the calibration medium should not exceed 1 ℃, and when completing the entire calibration process, it should not exceed 5 ℃; After each experiment, the valve at the front end of the test pipeline should be closed first, and then the pump should be stopped to avoid emptying the stabilizing facilities. At the same time, the remaining calibration medium in the test pipeline must be emptied, and the control system and air compressor must be turned off after the Baode BURKERT flowmeter is turned off.
ATOS proportional valve RZMA-030/180/M/7 32
Siemens actuator SKC62
Bornstein limit switch 6087385014
FIAMA FIAMA model FM01-H0200-E01-PU05-R201 comes with a 5-meter cable (including connectors, 5-meter cable, magnetic ring) to replace BTL7-E501-M0200-A-S32+BKS-S32-05
VICKERS coil 300AA0086A AC230 V
IFM laser sensor 01D106
Laser sensor 01D100
TURCK FXDP-IOM88- 0001
BERNSTEIN foot switch 6161000443 F1-UV1Z/UV1ZD
SMC solenoid valve ITV2050-312S3
HYDAC filter cartridge 0110D010ON/- V
Filter cartridge 0110D010BH4HC
Turck proximity switch FCS-G1/2A4-NA
HYDAC filter element 0110D010BH4HC
ASCO solenoid valve VCEFCMG551H401MO 24VDC
Xiangshile 0567010
Connector
Coupling
ATOS proportional valve AGMZO-REB-P-NP-10/210/I
GSR K0511890//230V50-60HZ8-11V+B0040.000047
Rexroth gear pump AZPF-12-004RCB20KB
Gear pump AZPF-10-011RCB20MB
Hedeke pressure sensor EDS1791-N-400-000