-
E-mail
hbdgyx@huangbeng.com
-
Phone
18005590168
-
Address
Building 6, Science and Technology Innovation Park, No. 12, Fengshan Road, Jiulong Industrial Park, Tunxi District, Mount Huangshan City, Anhui Province
Product Categories
Mount Huangshan Huangpu Single Screw Pump Co., Ltd
B-type bearing seat pump
NegotiableUpdate on 05/19
- Model
- Nature of the Manufacturer
- Producers
- Product Category
- Place of Origin
Overview
The B-type bearing seat pump has a stable structure and strong load-bearing capacity. It is suitable for high-pressure working conditions with a flow range of ≤ 400m ³/h and a working pressure of ≤ 4.8Mpa. It can transport various media containing solids, gases, and high viscosity
Product Details
Product advantages
- high stability
- Strong carrying capacity
- Suitable for high-pressure working conditions
- Wide applicability of the medium
- Continuous low pulsation conveying
- No compression and low shear
- Flow rate is proportional to rotational speed
- High pumping efficiency
-
Independent bearing seat structureCan bear higher axial loads
Better rigidity
Suitable for high-pressure working conditions
-
Process of grease lubricated bearingsChoose grease lubricated bearings
Fundamentally eliminate
Pump lubricating oil leakage problem
-
Reinforced cross universal jointImproved on the basis of traditional cross type universal joints
Greater load capacity
product structure
rotor
Can be paired with various materials and surface treatment solutions such as 40Cr, 304, 316L, 2205, etc
N-type geometric shape
The standard lead design of the rotor shows an increase in pressure for rotors of the same specifications
L-shaped geometric shape
Long lead design of rotor, extended sealing line, and increased flow rate of rotors of the same specifications
T-shaped geometric shape
The rotor has a geometric shape of a three headed spiral, and rotors of the same specification increase flow rate while considering high-pressure conditions
stator
Can be paired with various rubber solutions such as NBR, SBR, EPDM, HNBR, FKM, etc
Anti slip design
The rubber sealing rings at both ends of the stator are wrapped around the steel sleeve and formed as a whole to prevent the stator steel pipe from coming into contact with the medium and being corroded and slipping off
N-type geometric shape
The standard lead design of the rotor shows an increase in pressure for rotors of the same specifications
L-shaped geometric shape
Stator long lead design, extended sealing wire, and increased flow rate for rotors of the same specifications
T-shaped geometric shape
The stator has a three headed spiral geometry, and the flow rate of the same specification stator increases while considering high pressure conditions
Imported cavity
Multiple cavity materials including cast iron, carbon steel, austenitic stainless steel, or duplex stainless steel are available for selection
Adjustable import direction
The orientation of the cavity can be adjusted according to the on-site piping requirements to be either upward or downward
Discharge outlet
The cavity is reserved with exhaust ports in all three directions for easy cleaning
universal joint
Multiple universal joint materials including carbon steel, austenitic stainless steel, or duplex stainless steel are available for selection
Enhanced design
Equipped with reinforced cross universal joint structure, with stronger load capacity
shaft seal
Different shaft seal schemes and various sealing flushing system schemes can be selected according to the medium
packing seal
Packing sealing is economical and convenient, requiring a small amount of leakage to ensure sufficient lubrication of the transmission shaft
mechanical seal
The standard configuration is SiC SiC material, and different materials and forms of mechanical seals can also be selected according to the medium conditions
drive
Equipped with a standard deceleration motor drive, motors with different functions such as variable frequency/explosion-proof/stepless speed regulation/electromagnetic speed regulation can also be selected according to needs. In special working conditions, hydraulic motors can be used to drive
Product Parameters
| Brand: Yellow Pump | Origin: Mount Huangshan, Anhui |
| Flow range: ≤ 400m ³/h | Work pressure: ≤ 4.8Mpa |
| Temperature range: 150 ℃ | Conveying medium: capable of conveying various solid/gas/high viscosity media |
| Installation method: Standard base and anchor bolts | Drive mode: electric/hydraulic |
noteThe above parameters are for reference only and are subject to change without prior notice
