Product Introduction

The system is suitable for weight determination of low concentration particulate matter in fixed pollution source exhaust gas. It can also be used for the cultivation and preservation of molds, microorganisms, antibiotics, and tissue cells; Research on plant cultivation, breeding experiments, enzymology, and enzyme engineering; Preservation and testing equipment for biological products, vaccines, blood, and various specimens.

Details

LB-500Constant temperature and humidity weighing system

1、 Scope of applicationConstant temperature and humidity weighing system with external split type air compressor

This system is suitable for the weight determination of low concentration particulate matter in fixed pollution source exhaust gas.Can also be used forCultivation and preservation of fungi, microorganisms, antibiotics, and tissue cells; Research on plant cultivation, breeding experiments, enzymology, and enzyme engineering; Preservation and testing equipment for biological products, vaccines, blood, and various specimens.

2、 Structural characteristicsConstant temperature and humidity weighing system with external split type air compressor

• studioMade of mirror stainless steel, easy to clean, with adjustable spacing between shelves inside the box.
• Microcomputer temperature and humidity controller for temperature control (humidity control)Stable and reliable.
• The separate design of the refrigeration unit and the main engine can avoid the impact of compressor operation on the testing environment.
• Internal humidification mode can save water and energy.
• The air duct is equipped with heaters, refrigerators, dehumidifiers, humidifiers, and temperature and humidity sensors.
• organicGlass door observation window, installed inside the boxLEDLighting fixtures for easy and clear observation.
• The countertop in the studio is resistant to acid and alkali corrosion.

3、 Main technical parameters

Model: LB-500

Temperature control range:10-35°

Temperature fluctuations:±0.5℃

Humidity range:20~80%RH

Humidity fluctuation: ±3%RH

Power consumption: 1300W

Size: 1230 (length) ×650(Width) × 1710(Height) mm

Weight: Approximately240Kg(Host)+50Kg (Refrigerator)

4、 Product installation and debugging

1. Be careful not to be in transitorganicApply force on the glass and do not collide with the box. Do not invert or tilt at an angle greater than 45 degrees.

2. After landing, this device should be placed steadily. If the ground is uneven, it should be corrected.The ground should be flat, vibration free, and have high hardness.

3The equipment is installed in a clean laboratory,Do not use the instrument in direct sunlight or in areas with high temperature and humidity. Keep the operating environment temperature at5-30℃，Environmental humidity ≤ 85%.

4. This device should be kept away from electromagnetic interference sources and the grounding wire of the device should be effectively grounded.

5. When this device is operating normally, the placement of the contents inside the box should not affect air circulation to ensure air circulation and uniform temperature inside the box.

6. The power supply is AC 220V 50HZ and must be usedEquipment power cordDo not act without authorizationChange power cord.

7. Do not place the power cord close to the back, and do not let instruments or other objects press on the power cord to avoid damaging it.

8. Connect the host to the refrigeration unit.

5、 Product Instructions

1. Open the box door, place the items to be processed on the shelves inside the box, and close the outer doors one by one.

2. Fill the humidifier water tank with water. (It is recommended to use purified water)

3. Connect the power supply, insert the three pin plug into the power socket, and place the power switch on the back of the panel in the "on" position (the switch indicator light is on). At this point, the device has been powered on internally and the operating part is in the standby state. Manually press and hold the 2S start operation switch, and the instrument will display a number, indicating that the device has entered the working state.

4. Set the desired temperature and humidity inside the box by operating the temperature and humidity controller on the control panel.

5. The instrument starts working, and the temperature and humidity inside the box gradually reach the set values. After the required processing time, the processing work is completed.

6. Turn off the power, wait for the temperature inside the box to approach the ambient temperature, open the box door, and remove the object.