Characteristics of Parker filters in the United States

Characteristics of Parker filters in the United States
filterIt is a device on the pipeline, usually installed at the inlet end of pressure reducing valves, relief valves, fixed water level valves, square filters, and other equipment. The filter consists of a cylinder, a stainless steel filter screen, a discharge part, a transmission device, and components. After the water to be treated passes through the filter cartridge of the filter screen, its impurities are blocked. When cleaning is needed, simply remove the detachable filter cartridge, process it, and reinstall it. Therefore, it is extremely convenient to use and maintain. High pressure filters are suitable for filtering out solid and liquid impurities in compressed air below 4Mpa. Also known as: high-pressure filter, compressed air high-pressure filter, high-pressure oil-water separator, high-pressure air filter, air source high-pressure filter, instrument air high-pressure filter, etc.
Parker filter from the United StatesMainly installed on the return oil pipeline of the hydraulic system, various types of hydraulic components can intercept various pollutants such as abrasive particles generated during operation by setting an oil filter in the return oil pipeline, avoiding them from returning to the oil tank and being sucked into the hydraulic pump again The allowable pressure difference of the oil filter in the return oil pipeline ranges from 0.3 to 0.5 MPa depending on different pressure levels. The accuracy is determined specifically according to the requirements of oil contamination level.

There are more factors to consider when setting up Parker return oil filters in the United States, and one important factor is hydraulic shock, especially when there are hydraulic cylinders and proportional valves upstream. Under high pressure, the directional change of the hydraulic cylinder and the sudden power failure of the proportional valve will produce a large instantaneous flow shock, which will cause great damage to the filter element of the oil filter. When designing and selecting return oil pipeline oil filters, it is necessary to have a full understanding and strengthen the structure. The company guarantees original factory shipment, good performance, complete models, and short lead time.

Performance characteristics of Parker filters in the United States
There are four types of return oil filters: fiber type, paper type, mesh type, and wire gap type. Chemical fiber filters have better filtration effects and higher accuracy than paper filters. It is difficult to clean clogged chemical fiber and paper filters, so they must be replaced. The return oil filter is equipped with a differential pressure transmission device. When the filter element is clogged due to pollution and the pressure difference between the inlet and outlet reaches 0.35MPa, a switch signal is sent out. At this time, the filter element should be cleaned or replaced. The filter element of this filter adopts a new type of synthetic fiber filtration material, which has the advantages of high filtration accuracy, large oil flow capacity, low original pressure loss, and large pollutant holding capacity. Its filtration accuracy is calibrated based on filtration accuracy, with filtration ratios of p3, 5, 10, and 20>100, and filtration efficiency n ≥ 99%, in compliance with ISO standards.

Application scope of Parker filters in the United States
1. Metallurgy: Used for filtering hydraulic systems of rolling mills and continuous casting machines, as well as filtering various lubrication equipment.
2. Petrochemicals: Separation and recovery of products and intermediate products in refining and chemical production processes, as well as particle removal and filtration of oilfield injection water and natural gas.
3. Textile: Purification and uniform filtration of polyester melt during wire drawing process, protective filtration of air compressor, and removal of oil and water from compressed gas.
4. Electronics and pharmaceuticals: pre-treatment filtration of reverse osmosis water and deionized water, pre-treatment filtration of cleaning solution and glucose.
5. Thermal power and nuclear power: Purification of oil for lubrication systems, speed control systems, bypass control systems of gas turbines and boilers, purification of feed pumps, fans, and dust removal systems.
6. Mechanical processing equipment: lubrication systems and compressed air purification for paper making machinery, mining machinery, injection molding machines, and large precision machinery, filtration for tobacco processing equipment and spraying equipment.
Parker filter model in the United States:
BGT1210QLBPER323
BGT1220QLBPER323
BGT1510QLBPER483
BGT1520QLBPER483
BGT1710QBPER483
BGT1720QBPER483
BGT1210QLBPER323
BGT1220QLBPER323
BGT1510QLBPER483