Automatic constant temperature heating small reaction kettle

Produced by our factoryAutomatic constant temperature heating small reaction kettleFor a flat top,Lower archeadsingleLayer structure.With a top cover,Equipped with heating, automatic temperature control, and insulation，beltMixing function;And the stirring speed can be adjustedAdaptationChemical plants or surface treatment units carry out small componentsCleaningPassivation, useAdvantages such as convenience.

OneApplication areas of ingredient tanks:

Electric heating mixing and batching tankWidely used in industries such as food (dairy) products, pharmaceuticals, daily chemical products, beverages, oils, chemicals, pigments, etc. for heating, mixing, or sterilization treatment. Suitable for small and pilot scale use in units and research institutions without steam heat sources. And a fully enclosed structure can be adopted according to the process requirements.

IIAutomatic constant temperature heating small reaction kettleMain technical and structural performance:

• The diameter of the mixing tank is 1000mm, the depth is 1200mm, and the plate thickness is 3.0 stainless steel 304. The bottom of the tank is elliptical.
• The mixing motor has a power of 1.5KW and is equipped with a frequency converter of 3KW. The reducer adopts a vertical cycloidal gear, and the speed can be adjusted from 0-11.5 revolutions per minute. The mixing blade has two layers and is of the blade type.
• The bottom frame is formed by welding 100X50 stainless steel rectangular tubes, and the material is poured using electric discharge with automatic reset. The motor power is 0.75KW, and there is a crossbeam at the upper opening of the mixing tank to install the mixing device, while the rest do not have a cover plate.

4. stircanVolume:900L

5. Mixing device: Top center mixing,The mixing blade adopts a blade type, and the height and position of the activity can be adjusted,The output shaft of the reducer and the agitator shaft are connected by a flexible sleeve, making it easy to disassemble, assemble, and clean，Please carefully read the instructions for using the frequency converter when starting up.

6Equipment control configuration: electrical control box, power supplyswitch、Inlet and outlet valvesFrequency conversiongovernorWait.
7Material: Inner tank body made of stainless steel 304 3.0wire drawingBoard;

threeQuick operation:

1. Due to the four corner fixed plates of the mixing tank, in the equipmentReady in placeFix the ground with expansion screws and secure the mixing tank before use.

2．Please carefully read the instrument and motor manuals of all accessories on the equipment, and then follow the circuit diagram and standard wiring methodTurn on the powerBe sure to ensure that the mixing tank is properly grounded before use (the grounding wire connector is located on the edge of the inlet hole with an M6 terminal post),againClose the circuit breaker.

3. Open on the control boxtotalTurn on the power knob, and the power indicator light will turn on.

4．Start mixing before feeding, and never start mixing after feeding, as this can cause significant damage to the mixing device. The operating speed needs to be controlled and adjusted by the user themselves during operation）

5. Turn on the mixing knob before feeding, and thenAdjust the mixing speed according to the instruction manual of the frequency converter,averagenot less thanAt 20 Hz, the stirring indicator light will turn on to prevent material sedimentation.（It is recommended that the frequency of the frequency converter should not be lower than 20 Hz, and it is also not recommended to operate at high speed for a long time, as this is beneficial for protecting the mixer and motor）

6. At this point, it has entered the normal heating working state，When the mixing work is completed, press the discharge button, which is a jog button. To ensure safety, please do not hold it down for a long time. After discharging, please press the reset button, which is also a jog button, to restore the tank to its normal upright state and continue with the next operation.

7The device cannot be left unattended. If the device is damaged without supervision, the consequences shall be borne by the user.

8At the end of the work, follow the reverse procedure to shut down the device.

9After discharging the material, it should be promptly placed inQingWater is used to cool the pot wall. To achieve the purpose of protecting the machine.