ice crusherOperation method:

　ice crusherIt should be installed on a workbench with sufficient support and at an appropriate distance from the ground; Before connecting the power supply, check whether the voltage of the power supply used matches the voltage used by the machine, whether the socket meets safety standards, and whether the leakage protection switch and grounding wire have been installed. Confirm that everything meets the requirements for electricity usage; Before starting up, crush the ice cubes to a diameter of about 20 millimeters before placing them into the material cylinder, with the top protruding above the cylinder mouth. Pay attention to turning on the power switch first, and only allow the plate dynamic pressure material cover handle to press down after the electric motor rotates with the power plate. At this time, cut the ice cubes into small pieces by fastening the blades on the rotating blade. But when operating the pressure cover handle to press down, do not apply too much force to avoid motor blockage and damage to the motor. And attention should be paid to the remaining amount of ice material after reduction, and new ice blocks should be replenished in a timely manner; The chopped ice particles flow into the tray through the discharge port. Pay attention to the smooth discharge of the discharge port and avoid blockage, otherwise it may cause the knife disc to get stuck and burn out the motor. If the cutterhead is found to be stuck, immediately lift the handle of the pressing cover, turn off the switch, unplug the plug, and promptly troubleshoot the problem; The thickness of ice particles can be achieved by adjusting the height of the blade mouth protruding from the cutter head. To adjust, first remove the plastic disc of the protective switch device, loosen the screw fixing the bent pipe, pull out the material cylinder, then loosen the fastening screw of the cutter head, remove the cutter head, and then loosen the clamping screw of the blade. Install it in place according to your requirements, and then install the cutter head and other components back in place in order.

useice crusherAttention should be paid to:

1. To ensure safety, it is not allowed to directly press the ice block with hands for cutting.

2. After each use, it must be cleaned. When cleaning, the main power switch should be turned off, the plug should be unplugged, and then a clean towel should be used to wipe the water off the machine. After cleaning, remember to lift the handle of the pressure cover.

3. Cleaning agents are not allowed during cleaning to prevent contamination caused by residual cleaning agents on the machine. Do not rinse directly with water to prevent electrical components from getting damp, affecting safe use, and damaging the machine.

4. The motor of this machine is designed with a temporary cut-off rate of 80% to avoid prolonged continuous operation. After working continuously for one hour, pause for twenty minutes before resuming work. This will greatly extend the service life of the electric motor.

5. Whether it is cleaning, repairing, replacing blades, or cleaning debris, the power should be turned off first and the power plug should be unplugged; We are not allowed to operate without load for a long time.

　　ice crusherOperation method:

　ice crusherIt should be installed on a workbench with sufficient support and at an appropriate distance from the ground; Before connecting the power supply, check whether the voltage of the power supply used matches the voltage used by the machine, whether the socket meets safety standards, and whether the leakage protection switch and grounding wire have been installed. Confirm that everything meets the requirements for electricity usage; Before starting up, crush the ice cubes to a diameter of about 20 millimeters before placing them into the material cylinder, with the top protruding above the cylinder mouth. Pay attention to turning on the power switch first, and only allow the plate dynamic pressure material cover handle to press down after the electric motor rotates with the power plate. At this time, cut the ice cubes into small pieces by fastening the blades on the rotating blade. But when operating the pressure cover handle to press down, do not apply too much force to avoid motor blockage and damage to the motor. And attention should be paid to the remaining amount of ice material after reduction, and new ice blocks should be replenished in a timely manner; The chopped ice particles flow into the tray through the discharge port. Pay attention to the smooth discharge of the discharge port and avoid blockage, otherwise it may cause the knife disc to get stuck and burn out the motor. If the cutterhead is found to be stuck, immediately lift the handle of the pressing cover, turn off the switch, unplug the plug, and promptly troubleshoot the problem; The thickness of ice particles can be achieved by adjusting the height of the blade mouth protruding from the cutter head. To adjust, first remove the plastic disc of the protective switch device, loosen the screw fixing the bent pipe, pull out the material cylinder, then loosen the fastening screw of the cutter head, remove the cutter head, and then loosen the clamping screw of the blade. Install it in place according to your requirements, and then install the cutter head and other components back in place in order.

useice crusherAttention should be paid to:

1. To ensure safety, it is not allowed to directly press the ice block with hands for cutting.

2. After each use, it must be cleaned. When cleaning, the main power switch should be turned off, the plug should be unplugged, and then a clean towel should be used to wipe the water off the machine. After cleaning, remember to lift the handle of the pressure cover.

3. Cleaning agents are not allowed during cleaning to prevent contamination caused by residual cleaning agents on the machine. Do not rinse directly with water to prevent electrical components from getting damp, affecting safe use, and damaging the machine.

4. The motor of this machine is designed with a temporary cut-off rate of 80% to avoid prolonged continuous operation. After working continuously for one hour, pause for twenty minutes before resuming work. This will greatly extend the service life of the electric motor.

5. Whether it is cleaning, repairing, replacing blades, or cleaning debris, the power should be turned off first and the power plug should be unplugged; We are not allowed to operate without load for a long time.