Wholesale high-density anti-corrosion pipeline wooden pallets

Wholesale high-density anti-corrosion pipeline wooden pallets

Thickness of board and insulation layer: 30 * 30 mm 40*40mm 50*50mm 60*60mm 80*80mm 100*100mm 150*150mm 200*200mm 250*250mm 300*300mm Nominal diameter of pipeline: DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100 DN125 DN150 DN200 DN250 DN300 DN350 DN400 Customization of DN1000 pipes is available for both special-shaped and non model pipe wooden supports. Φ27、 34, 43, 48, 60, 76, 89, 108 are used for fixing and installing PPR air conditioning ducts, and can be used as iron clips for fire and chemical pipelines.
4>Φ273、 325, 377, 426, 480 are used for fixed installation and scaffolding of main and underground pipelines. Knowledge Expansion and Extension: Thirdly, the steel pipe welding sub item is applicable to the welding of welded steel pipes, seamless steel pipes, and other steel pipes.
4、 The sealing material for pipeline threaded connections takes into account both hemp and PTFE tape, but in reality, it is different and cannot be adjusted.
5、 The installation of outdoor plastic water supply pipes has comprehensively considered the connection methods such as bonding, electric welding, rubber rings, and threaded connections. When applying the sub items, the materials of the pipes and fittings can be converted according to the actual situation. But when using rubber ring connection, the rubber ring material should be calculated according to the actual situation; When using electric fusion welding, the material of the electric fusion sleeve should be calculated according to the actual situation. (5) Final treatment (final treatment, final treatment): Final treatment is carried out after the wood has been balanced or after the actual moisture content of the wood that does not require balance treatment reaches the required final moisture content.
Dry bulb temperature: 5-8 ℃ higher than the dry bulb temperature in the post drying stage, but not exceeding 100 ℃.
Wet bulb temperature: 3-4 ℃ lower than the dry bulb temperature during processing. If a balanced moisture content device is used, the balanced moisture content value can be set to 13% -14%.
Retention time: You can refer to the initial processing time, or shorten it by 1-2 hours compared to the initial processing time.
The effectiveness of the final treatment should be based on the actual inspection of whether the residual stress index of the wood meets the requirements of the grade wood quality standards. For secondary materials that are not cut after drying, a certain residual stress is allowed, and the final treatment may not be strict

The product is easy to install, has strong anti insulation and anti vibration properties, has a long service life, is energy-saving and environmentally friendly, beautiful, and can be disassembled and reused multiple times. It is your trusted choice. Our company's pipeline pad products are sold all over the country. Used for fixing and installing indoor welding pipes in buildings. Model and specifications:
1、 Insulation layer 30 * 30 type
2、 Insulation layer 40 * 40 type
3、 Insulation layer 50 * 50 type
4、 Insulation layer 80 * 80 type
5、 Insulation layer 100 * 100 type
6、 Insulation layer 150 * 150 type
Both Φ 27 and Φ 1020 can be customized for knowledge expansion and extension: for support and hanger brackets rooted in buildings and structures, their rooting points should be set on load-bearing structures such as columns or main beams. When the rooting parts of the brackets are welded to equipment that requires overall heat treatment, the conditions for the used pads should be proposed to the equipment profession. (7) When it is necessary to limit the displacement of pipelines, limit brackets should be installed. (8) High temperature pipelines, low-temperature pipelines, vibration pipelines, and steam pipelines shall not be used to support other pipelines. (9) Flat mounted valves with a nominal diameter equal to or greater than 150mm that are directly connected to or close to the equipment pipe mouth should consider support. (10) Vertical pipes arranged along vertical equipment should be equipped with load-bearing brackets and guide brackets. The large spacing between riser supports should comply with regulations. The load-bearing bracket should be placed near the equipment pipe mouth to reduce the stress on the pipe mouth. If the weight of the pipeline is too large and it is difficult for a support to bear weight, a variable spring load-bearing support can be added. (11) The distance between the edge of the support hanger and the weld seam of the pipeline should not be less than 50mm, and the distance between the support hanger or pipe bracket and the weld seam of the pipeline that requires heat treatment should not be less than 100mm. (12) When the support hanger or pipe bracket must be directly welded to the alloy steel pipeline, the material of its connecting components should be the same as that of the pipeline. It is known as the 'South American Lumber'. Wood is highly resistant to decay and has strong natural durability. Some uses can replace teak wood. Due to the presence of small silicon particles in the wood tissue, sawing wood is difficult and can cause the cutting edge to become dull. Therefore, alloy steel saw blades are used for sawing. The precision machined surface is smooth, with moderate adhesive properties, difficult to nail, and high gripping force. Used for interior decoration, furniture, pipe supports, stair handrails, building construction, etc., it is currently the most popular pipe support material in the market

Wholesale high-density anti-corrosion pipeline wooden pallets