Crude oil water content analyzer

OY-HS8100 Crude Oil Moisture Analyzer

User Manual

1、 Product model and name

OY-HS8100 Crude Oil Moisture Analyzer

2、 Purpose and scope of use

(hereinafter referred to as this machine) can be widely used

It is an ideal experimental instrument for research institutes and various petroleum industries in fields such as petroleum industry, biochemistry, genetic engineering, and scientific research institutions.

3、 Basic parameters:

Zui High Speed: 5000r/minTiming range:0~99min

Maximum centrifugal force: 4390xgSpeed control accuracy: ±50r/min

Zui Large Capacity:4×100mlNoise: ≤60dB(A)

Power supply:AC220V 50HZ 5ATemperature range: Room temperature~80 ℃

Features:

1. This instrument adopts a heating sleeve for non open flame heating, with fast heating, low power, uniform heating, and high efficiency.

2. Magnetic stirring is a closed magnetic stirring method that avoids sudden boiling and achieves rapid oil-water separation.

3. In the automation and self-control parts, the timer is the heating power switch, which sets the required time and automatically shuts down the power when the time is up. By using gas sensing probes instead of manual monitoring, if the height of oil and gas rise exceeds the specified standard, the instrument automatically cuts off the power supply and starts the axial flow fan to quickly cool down the furnace body, thereby avoiding the phenomenon of sudden boiling and sample collision and achieving safety.

4. Equipped with a pure water automatic cooling tank, it prevents the yellowing and scaling of glass instruments, and solves the problem of water shortage in field operations. 5. The DGN model is equipped with a glass instrument quick drying oven and a heating air duct for condensing air drying. In order to address the impact of external cold air on the receiver, it is equipped with a temperature protection device, which solves the problem of premature condensation of water vapor and backflow of water droplets, achieving the goal of rapid evaporation of moisture. HL1000 model, equipped with XA hot air flow rapid constant temperature dilution instrument, it can heat 6 samples at once and also dry glass instruments.



Operating Procedures
1. The power of each thermal group of the instrument is equal, and there is only one probe. When in use, after each group of oil samples is prepared, they must be loaded into the heating sleeve of the instrument and heated for distillation at the same time, otherwise the timer will lose its timing function.
2. The loading and unloading methods of the flask, receiver, and condenser tube: After the crude oil and diluted gasoline are loaded, the flask must be held by hand, and the receiver must be inserted into the flask with the left hand. Observe whether the grinding mouth of the flask and the grinding mouth of the receiver are tightly combined, otherwise there will be air leakage. Use your left hand to push the condenser tube up to the stop point, and your right hand to push it up. Insert the grinding mouth on the top of the receiver and the grinding mouth on the bottom of the condenser tube tightly into place. Align your left and right hands with the heating jacket and apply slight force until the bottom of the flask and heating jacket are tightly combined.
3. The usage method of automatic control probe: The probe is a substitute for manual monitoring of guards. Its principle is that oil and water are heated, and the oil and gas rise and come into contact with the probe to function. When in use, it must be inserted into the upper 1/3 of the heating condenser tube, otherwise it will not function automatically. The digital temperature control meter corresponding to the probe, such as a "voltage regulating instrument", should generally set the temperature at 60 degrees. For the "No Voltage Adjustment Instrument", the temperature should be set at around 35 degrees, relying on the principle of repeated oil sample flushing to accelerate oil-water separation. This temperature can be determined according to the actual situation of flushing. If the oil sample is flushed to 3/4 of the condenser tube, the temperature of the temperature control instrument can be set lower. If the oil sample is not flushed to 1/2 of the condenser tube, the temperature of the temperature control instrument can be set higher. These situations are related to the ambient temperature and oil sample density. Therefore, it needs to be flexibly applied. The adjustment of the intelligent temperature control meter is described in the following instructions.